Traffic and Parking Control Co., Inc. - Traffic Signal Division, LED ARROWS,arrow leds,led,led beacon,led electronics,led flashers,led lights,led products,led safety light,led signs,led traffic light

	TRAFFIC & PARKING CONTROL CO., Inc. 1.800.236.0112

Dialight LED Arrow (Meets 1999 ITE Specifications)

Specifications:

Fuse and transient suppressor incorporated for line and load protection1
Power factor greater than 0.92
Total Harmonic Distortion <20%2
Meets FCC Title 47, Subpart B, Section 15 regulations for electrical noise
Conforms to NEMA Moisture Resistance STD. 250-1991 for Type 4 enclosures (ITE 6.4.6.2 Moisture Resistance)
Provided with quick connect terminals. Space tab adaptor.
Operating Voltage Range:
80VAC TO 134 VAC (120VAC nominal)
Operating Temperature Range: -40°C to +74°C

1 Bi-Modal Green/Amber has transient suppressor only
2 Non applicable Bi-Modal Green/Amber

12" (300mm) - 120 Volt Arrows
TAPCO Part No.	Manufacturer Part No.	Note	Description	Volts	Typical Wattage @ 25ºC	Dominant Wavelength (nm)	Lens Tint
220-18	432-1314-001	1, 2	Red, 3 Row	120VAC	6.5	622	Red
220-14	431-3334-001	1	Yellow, 3 Row	120VAC	8.8	590	Yellow
220-17	432-2324-001	1	Green, 3 Row	120VAC	7.0	505	Clear
1 Approved by Caltrans 2 Meets or exceeds IE VTC Part 2

LED Arrows (Meets 2005 ITE Specifications)

Enlarge

Lighting Uniformity • ITE Conformity

Features / Benefits

Uniform non-pixelated appearance
Expanded view radiation pattern meets ITE VTCSH-3 LED Arrow Specification
90% reduction in power vs. incandescent
Long life: up to 10 times longer than incandescent
Fuse and transient suppressor incorporated for superior line and load protection
Hard coated lenses for abrasion resistance
Easy to install into existing signal enclosure

Specifications:

Operating Voltage Range: 80VAC TO 135 VAC (120VAC nominal)
Operating Temperature Range: -40°C to +74°C
Meets FCC Title 47, Subpart B, Section 15 regulations for electrical noise
Conforms to MIL-STD-810F for blowing rain
Conforms to MIL-STD-883, Test Method 2007, for mechanical vibration
Conforms to MIL-STD-883, Test Method 1010, temperature cycling requirements
Provided with quick connect terminals and spade adapters
All products traceable by serial number
Luminance uniformity and color uniformity exceed ITE PTCSI-2 LED Pedestrian Signal Specification requirements
Transient Suppression exceeds ITE PTCSI-2 LED Pedestrian Signal Specification requirements and meets the following standards:
- NEMA TS-2 Sec. 2.1.6 and Sec. 2.1.8
- IEC 1000-4-5, 3KV, 2 ohm source impedance
- ANSI/IEEE C62, 41-2002; IEC 61000-4-12,6KV, 200A, 100KHz ring wave

12" (300mm) - 120 Volt Arrows
TAPCO Part No.	Manufacturer Part No.	Color	Lens Type	Typical Wattage @25° C	Dominant Wavelength (nm)	Peak Minimum Maintained Luminous Intensity (cd/m2)
2406-6	432-1314-001X	Red	Tinted	7	625	59
2406-5	431-3334-001X	Yellow	Tinted	9	590	146
2406-4	432-2324-001X	Green	Tinted	7	500	76
* Currently yellow arrows are not eligible