Traffic and Parking Control Co., Inc. - Traffic Signal Division, Pedestrian LED Signal Options, digital led signs,electronic led signs,electronic signs,flashing led,led electronics,led flashers,led light emitting diode,led lights,led products,led safety light,led signs,led traffic light,led traffic signals

	TRAFFIC & PARKING CONTROL CO., Inc. 1.800.236.0112

Hand/Walking Person Combination LED Pedestrian Signals

Pedestrian LED Traffic Signal Options
(Meets 1999 ITE Specifications)

Features

2-Row, 9" high countdown digits are MUTCD compliant for crosswalks over 100 ft.
Full preemption compatibility - Reverts to its previous timing immediately following a preemption call.
Unique memory feature allows countdown time to remain stored internally, even when power is removed for extended periods of time.
Up to 4 units can be connected in parallel without disturbing the monitoring of the Hand/Person.
Automatically adjusts to traffic controller interval changes.
90% reduction in power vs. incandescent.
Long life: up to 10 times longer than incandescent.
Sealed moisture resistant enclosure.
Lens available to fit most pedestrian heads.
Lens has a textured surface to reduce glare.
Easy to install into existing signal enclosure.

Specifications

Operating Voltage Range: 80VAC to 135 VAC (120V nominal)
Fuse and transient suppressor incorporated for line and load protection
Operating Temperature Range -40°C to +74°C
Meets FCC Title 47, Subpart B, Section 15 Regulations for electrical noise
Provided with quick connect terminals and spade adapters
LED Colors:
Countdown Numerals - Portland Orange
Hand - Portland Orange
Walking Person - Lunar White

TYPICAL OPERATING CHARACTERISTICS

Uniform Appearance Hand and Person Pedestrian Signals

Pedestrian LED Traffic Signal Options
(Meets 2005 ITE Specifications)

Lighting Uniformity • ITE Conformity

Features / Benefits

Uniform non-pixelated appearance
Exceeds ITE PTCSI Part 2 requirements for LED pedestrian signals
Fuse and transient suppressor incorporated for superior line and load protection
90% reduction in power vs. incandescent
Long life: up to 10 times longer than incandescent
Sealed moisture resistant enclosure
Lens has a textured surface to reduce glare
Easy to install into existing signal enclosure

Specifications

Operating Voltage Range: 80VAC TO 135 VAC (120VAC nominal)
Operating Temperature Range: -40°C to +74°C
Meets FCC Title 47, Subpart B, Section 15 regulations for electrical noise
Failed State Impedance > 250K ohm within 300 ms
Conforms to MIL-STD-810F for blowing rain
Conforms to MIL-STD-883, Test Method 2007, for mechanical vibration
Conforms to MIL-STD-883, Test Method 1010, temperature cycling requirements
Provided with quick connect terminals and spade adapters
All products traceable by serial number
Symbol Colors:
- Upraised Hand - Portland Orange
- Walking Person - Lunar White
Transient Suppression exceeds ITE PTCSI-2 LED Pedestrian Signal Specification requirements and meets the following standards:
- NEMA TS-2 Sec. 2.1.6 and Sec. 2.1.8
- IEC 1000-4-5, 3KV, 2 ohm source impedance
- ANSI/IEEE C62, 41-2002; IEC 61000-4-12, 6KV, 200A, 100KHz ring wave
Power supply is conformally coated for robust operation

9" Pedestrian Signal LEDs are also available. Call for details. 1.800.236.0112
TAPCO Part No.	Manufacturer Part No.	Color	Lens Type	Typical Wattage @25° C	Dominant Wavelength (nm)	Minimum Luminous (cd/m2) Hand	Minimum Luminous (cd/m2) Person
2406-16	430-6450-001X	16 x 18	Side-by-side Hand and Person	8	7	1,400	2,200
2406-8	430-6472-001X	16 x18	Overlay Hand and Person	8	6	1,400	2,200
2406-15	430-5770-001X	12 x 12	Hand only	8	N/A	1,400	N/A
2406-14	430-7771-001X	12 x 12	Person only	N/A	7	N/A	2,200
2406-7	430-7772-001X	12 x 12	Overlay Hand and Person	8	6	1,400	2,200

Uniform Appearance Countdown Pedestrian Signals

Pedestrian LED Signal Options
(Meets 2005 ITE Specifications)
Lighting Uniformity • ITE Conformity

Features / Benefits

Uniform appearance symbols exceed ITE PCSI-2 requirements
9" high, 2-row countdown digits for maximum visibility
Countdown is fully MUTCD-compliant (even for crosswalks over 100 ft.)
Unique memory feature allows countdown time to remain stored internally, even when power is removed for extended periods of time
Full preemption compatibility. Countdown reverts to its previous timing immediately following a preemption call
Up to 4 units can be connected in parallel without disturbing the monitoring of the Hand/Person
Automatically adjusts to traffic controller interval changes
90% reduction in power vs. incandescent
Long life; up to 10 times longer than incandescent
Sealed moisture resistant enclosure
Lens has a textured surface to reduce glare
Easy to install into existing signal enclosure

Specifications

Operating Voltage Range: 80VAC TO 135 VAC (120VAC nominal)
Operating Temperature Range: -40°C to +74°C
Turn-on/Turn-off time < 75 msec
Power Factor > 0.9
Total Harmonic distortion < 20%
Meets FCC Title 47, Subpart B, Section 15 regulations for electrical noise
Conforms to MIL-STD-810F for blowing rain
Conforms to MIL-STD-883, Test Method 2007, for mechanical vibration
Conforms to MIL-STD-883, Test Method 1010, temperature cycling requirements
Provided with quick connect terminals and spade adapters
Written manufacturer’s warranty available on request
All products traceable by serial number
Luminance uniformity and color uniformity exceed ITE PTCSI-2 LED Pedestrian Signal Specification requirements
Transient Suppression exceeds ITE PTCSI-2 LED Pedestrian Signal Specification requirements and meets the following standards:
NEMA TS-2 Sec. 2.1.6 and Sec. 2.1.8
IEC 1000-4-5, 3KV, 2 ohm source impedance
ANSI/IEEE C62, 41-2002; IEC 61000-4-12, 6KV, 200A, 100KHz ring wave.

TYPICAL OPERATING CHARACTERISTICS